Then you would need the new P.C. Note, that even if the above test passes, there is another test for the optics board to test another function of the optic boards. To test the optics board, perform the steps at the top of the page. Reply skw Posted on May 7, 2015 I found my optic control board full of frozen water along with frozen water up into the water line frozen into the ice fill http://protectfileapps.com/ice-maker/kenmore-ice-maker-red-light-blinking-twice.html
After you create your account, you'll be able to customize options and access all our 15,000 new posts/day with fewer ads. I was one of the lucky 5% that did not have to get past Figure 1. Did I stumbled on a "reset" or optics reboot? I've tested all the wires for broken connection, I have perfect connection.
Open the Freezer door for and activate the freezer door switch 3 times within 10 seconds (see Figure 6 above). 6. Note the normal position for the ice maker armature to be in when NOT in harvest mode is shown in Figure 10 below. If you would like more assistance, reply to this thread and I will be glad to assist you further. If you do not feel confident repairing this problem yourself, then you can
Ice Level Optics Control Board Kit - Part # W10757851 Posted in Refrigerator Leave a reply 60 Thoughts on "W10757851 Ice Level Optics Board Diagnostics & Replacement" Kay Posted on I hope this will help you. It took about 5 minutes to install, and it works like a charm. Kenmore Ice Maker Not Making Ice Try turning down the temp in the fridge part of the unit you may try putting a termometer in there to gauge where it should be adjusted to, about 38-41 degrees
Reply jim Posted on March 17, 2015 I have replaced valve and ice maker is still not making ice. Whirlpool Ice Maker Reset Button Pour about 2/3 cup of water into the icemaker . Seems to me like there's no signal being sent from the icemaker to the water valve. http://www.applianceblog.com/mainforums/threads/1688-Kenmore-Whirlpool-Ice-Maker-LED-Blinking-Codes It only took the appliance store about a day to get the part in (the part was a little pricier than you quoted, about $90 w/ tax).
Now I'm not much of a handyman and the tools you said I needed are pretty much the extent of my entire tool collection. Kitchenaid Ice Maker Not Making Ice Vice President: An expert whose answer got voted for 100 times. NO WARRANTY IS MADE OR IMPLIED REGARDING ANY PRODUCTS COVERED BY ANYONECANFIXIT.COM or ABSOLUTE TECHNOLOGIES, INC. Open the freezer door and immediately view the diagnostics red status light next to the ice maker’s on/off switch.
Your answer needs to include more details to help people. this website RepairClinic.com 450,869 views 3:32 Refrigerator Ice Maker Not Making Ice | www.goodappliancesuperstore.com - Duration: 3:08. Whirlpool Ice Maker Red Light Flashing It blinks twice continuously. Kenmore Ice Maker Red Light Blinking Twice Whirlpool GC5SHEXNS Side by... 11 Answers Noisy whirlpool condensor fan motor Whirlpool 25.6 cu.
If you don’t get any response from the diagnostic test… wait 5 minutes then unplug the refrigerator for 10 seconds to reset the ice maker control board and try again. http://protectfileapps.com/ice-maker/whirlpool-ice-maker-not-making-ice.html The rest was cake. The entire repair was very easy to do, and took a minimal amount of time. Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... Kitchenaid Ice Maker Blinking Red Light
Is that correct? However with the door closed neither dispenser for ice nor water works!!! Where is the PCB located? Check This Out There was mold in it.
Still no ice….please help the unit is only 2 hrs old. Whirlpool Ice Maker Infrared Sensor Loading... thank you by Manage My Life March 9th, 2012 Comment 0 votes Vicki, I hope the boards solve the problem.
I found a cube lodged in the plastic teeth which apparently stopped the sweeping rotation. Disconnect the wire harness on the top side and then remove the two Phillips screws to release the emitter control board from the housing. Re-install the emitter board in the reverse Reply Ryan Posted on July 16, 2015 Did you replace the optics boards with new OEM replacement part # W10757851? Kenmore Ice Maker Led Blinking Codes There is no blockage in the water fill tube.
But finally I got the wire harness to separate. Within the instructions, I will show you how to order your part (based on your model number of your refrigerator). Do I still have a problem? this contact form Help Me Find My Model Number Select Appliance Type: Air Conditioner Dishwasher Dryer Freezer Ice Machine Microwave Range/Stove/Oven Range Vent Hood Refrigerator Trash Compactor Washing Machine Model Number Locations Side Wall
French Door ... See Details Whirlpool WRT519SZDW 19 cu. How long will it take for the trays to fill and make ice? ft.
Sign in 136 Loading... Ft. Reply Kathie Posted on January 22, 2015 I do get 2 pause 2. I just heard the ice clunking a few minutes ago which was music to my ears.
If you realize that it was not current when you confirmed your PayPal contribution, please send me an email ([email protected]t.com) NOTE: Microsoft's Outlook Express is sometimes set not to allow viewing How To Test The Whirlpool Ice Maker Optic Control Boards W10757851 First, open the freezer door and look at the status LED on the right hand side. ApplianceVideo.com 276,852 views 7:21 Refrigerator Water Inlet Valve (part #W10408179)-How To Replace - Duration: 9:55. Figure 6 - Activate Freezer Light Switch 3 Times 5.